TPV
TPV pumps are single-stage monoblock centrifugal pumps with pipes in a line. The pumps are equipped with asynchronous electric motors with air cooling. Shafts of the pump and electric motor are connected to each other using a special intermediate shaft and keyed joint. The pumps are embedded with a mechanical shaft end seal, and its flow part is assembled with special bronze gap seals, increasing service life of pump components.
Characteristics
Pump family
—
TPV
Max flow
—
up to 1870 m³/h
Maximum head
—
up to 150 m
Max working pressure
—
16 / 25 bar
Liquid temperature range
—
-20 .. 140 °C
Max. ambient temp.
—
40 °C
TPV
TPV pumps are single-stage monoblock centrifugal pumps with pipes in a line. The pumps are equipped with asynchronous electric motors with air cooling. Shafts of the pump and electric motor are connected to each other using a special intermediate shaft and keyed joint. The pumps are embedded with a mechanical shaft end seal, and its flow part is assembled with special bronze gap seals, increasing service life of pump components.
Pump structure allows to remove a head part (motor, lamp and impeller) for technical or service maintenance keeping the pump on a pipeline. Radial and axial forces are accepted by motor bearings, so additional bearings are not needed in the pump part. Flow parts of the pump and impeller are covered with corrosion-resistant cataphoretic coating.
These pumps can be used various areas, the most common of which are listed below:
∙ centralized heat supply systems
∙ heating systems
∙ air conditioning systems
∙ centralized cooling supply systems
∙ water supply
∙ industrial processes
∙ industrial cooling
TPV pumps are suitable for pumping of non-viscous, explosion-proof and non-flammable liquids, not containing solid or fiber inclusions. If the pumped liquids have higher density and/or viscosity than water, it is recommended to use pumps with more powerful motors. Decision on whether a pump is suitable for pumping a particular liquid, depends on many factors, the most important of which is chloride contents, pH value, temperature and chemicals contents, etc. To assess compatibility with special liquids, contact Vandjord specialists.
Pump structure allows to remove a head part (motor, lamp and impeller) for technical or service maintenance keeping the pump on a pipeline. Radial and axial forces are accepted by motor bearings, so additional bearings are not needed in the pump part. Flow parts of the pump and impeller are covered with corrosion-resistant cataphoretic coating.
These pumps can be used various areas, the most common of which are listed below:
∙ centralized heat supply systems
∙ heating systems
∙ air conditioning systems
∙ centralized cooling supply systems
∙ water supply
∙ industrial processes
∙ industrial cooling
TPV pumps are suitable for pumping of non-viscous, explosion-proof and non-flammable liquids, not containing solid or fiber inclusions. If the pumped liquids have higher density and/or viscosity than water, it is recommended to use pumps with more powerful motors. Decision on whether a pump is suitable for pumping a particular liquid, depends on many factors, the most important of which is chloride contents, pH value, temperature and chemicals contents, etc. To assess compatibility with special liquids, contact Vandjord specialists.
Characteristics
|
Pump family
|
TPV |
|
Max flow
|
up to 1870 m³/h |
|
Maximum head
|
up to 150 m |
|
Max working pressure
|
16 / 25 bar |
|
Liquid temperature range
|
-20 .. 140 °C |
|
Max. ambient temp.
|
40 °C |
|
Housing material
|
чугун НТ250 |
|
Size of inlet connection
|
DN 32 - DN 350 |
|
Size of outlet connection
|
DN 32 - DN 350 |
|
Impeller material
|
cast iron НТ200 |
|
Motor standard
|
IEC |
|
Rated power – P2
|
0,75 - 315 kW |
|
Mains frequency
|
50 Hz |
|
Rated current
|
1,4 - 554 A |
|
Motor rotation speed
|
2900 / 1450 / 960 rpm |
|
Number of poles
|
2 / 4 / 6 |
|
Protection class (IEC 34-5)
|
IP55 |
|
Insulation class (IEC 85)
|
F |
|
Energy efficiency class
|
IE3 |
Documents
Photo gallery
1/3
—